Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinct SUV-like appearance due to its larger dimensions. Additionally, the wheel sizes of 19 inches in Ti and ST-L models can be firm at times. The front tyres on the Qashqai can also lose grip on rough surfaces, and the CVT could occasionally display wrist-flexing torque steering.

This is usually due to an unresponsive coin battery that is easily replaced in minutes. Make sure that the new battery is the same size, voltage and specifications.

Water Damage

One of the main reasons a Nissan key fob gives the "key ID is incorrect" message is due to water damage. The key fob comes with rubber seals that shield the electronic chip inside. However, prolonged exposure to moisture could cause it not to function properly. This is usually the case when you drop your key fob in the ocean or into a swimming pools, but it could be the case if it gets wet due to soapy hands or rain.

If your key fob has been exposed to water for a long period of time it is possible to clean it with isopropyl, or an electronic cleaner. It may also need to be taken to an expert to repair or replace it.

If your key fob is in need to be replaced, it is an easy process. Make sure you've got the correct multipack (CR2032, 3V). Open the back and front cases with an abrasive screwdriver. Remove the metal clips, then remove the battery that was in place and replace it. Reassemble the fob and replace the mechanical key. Check that it works properly. If not then you'll have to go to your local Nissan dealer or an experienced auto locksmith to replace the key chip. The chip is typically not damaged by water, so it should not cost a lot.

Dead Coin Battery

The coin battery is another common reason that your Nissan 350z key replacement Qashqai remote key fob may not work. They last for three to five years, but will eventually fail if the fob has been frequently dropped. You can replace the battery with a new one, but make sure that it's the same voltage and size as the original. If you choose to use a brand new battery, it could cause the key to be assigned an incorrect key ID. This will prevent it from being linked to your vehicle.

The most effective method of changing the battery inside a Nissan Qashqai Key Fob is to break it open using the help of a small screwdriver with a flat head. The screwdriver should be inserted into tiny notch at the bottom of the fob and twist gently to separate the two halves of the key fob. Remove the old CR2025 battery and replace it with a new one, noting the position of the previous one inside the fob.

Before you put the new battery into place ensure that there isn't any water damage or dirt on the terminals. If there is, wash the terminals using a small amount of isopropyl alcohol. Make sure that the pole cables are connected correctly. They should be connected to the negative and the positive poles of your battery.

Troubleshooting

If your Nissan Qashqai's key fob isn't working after being exposed to water that is clean from a tap or rain it could indicate that there's an issue with the internal chip. A battery change won't solve the issue, and you'll need to buy another key fob. If you dropped the key fob on the ground and it stopped functioning immediately it's most likely because it damaged the internal chip. It is possible to get the replacement key nissan qashqai fob back to function once more if you remove and clean the chip using paper towel and isopropyl alcohol and then put it back into.

Key ID Incorrect is a common mistake that you might see on the dashboard of your car. This means that the vehicle cannot recognize the key fob, and will not allow it to start the engine. This problem could be caused in numerous ways, including water damage, problems undetectable in the key fob's circuitry or RFID interference.

The key fob will cease to function in the event that the 12 volt batteries are not working or provide enough electric current. This could affect the Nissan Qashqai's remote keyless system central locking, as well as the capability to start the engine with the key fob. Check the battery in the key fob in case you are not able to lock and unlock your door manually. You could also try re-inserting the battery to reset the transmitter.

Reprogramming

If the key fob was not submerged in saltwater it should be restored to its original state by a simple wash of clean water. You can also try cleaning the electronic chip using isopropyl Alcohol or an electronic cleaner. If none of these methods work then you might need to replace the key fob.

If your Nissan Intelligent Key is still not working, there could be a problem with the connection between it and your car. To reconnect it, start by turning the key into the ignition without starting the car. Continue doing this until the hazard lights flash twice. Then, turn off the vehicle and take off the key.

Open the fob compartment of your vehicle. It's usually in the door jamb, on the handle for the driver's door, or under an armrest. Find the small "program" button and press it. You should hear a chime sound when the process is completed.

It's time to put your Intelligent Key to the test. Use all the buttons on the key while standing at a distance away from the car. If the lights flash and the horn sound it means the key has successfully connected to the Nissan. You may also try testing it in close proximity.