Repairs to uPVC Windows

uPVC windows are an excellent option for modern homes. They are durable, long-lasting and easy to maintain. They do not rot or rust like aluminum or timber.

It is important to clean and oil UPVC doors and windows on a regular basis. This will save you from unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows can cause significant damage to your home, and could even be fatal. It is crucial to take the time to ensure that you are doing everything you can to ensure that your windows are in good repair.

For single pane windows, it is fairly easy to replace them, and the replacement is usually able to fit into the frame that was previously installed easily. If you have double glazed window repairs near me-paned windows that are joined by internal beading, it is more difficult to remove and replace the old panes. In this instance you'll need source some plastic spacers that will assist the new pane to fit perfectly into the window frame.

Wearing protective eyewear and thick gloves is a must for anyone who plans to remove the glass by yourself. It is also a good idea to lay down a dropcloth before you begin working on the glass so that any shards fall onto the fabric rather than on the floor where they can be trodden under and cause further damage.

It's a good idea to seal the gap after the glass has been removed. This will stop water and drafts from entering your home until a professional arrives to repair the window. This will also act as a barrier that will prevent any intruders from getting access into your home. If the distance between the window and the door is substantial, you may prefer an alarm system that has windows. This will provide the best of both.

2. Sagging

uPVC is a durable and energy efficient alternative to timber sash windows. However, over time, they can suffer from a variety of issues, including sagging. A window that is sagging can cause problems with light, draughts and even security. It's crucial to act immediately if you realize that your uPVC windows are falling down.

Repositioning the hinges can help fix a window that is sliding. To accomplish this, you'll need to open the window to get to the frame. After that, using the screwdriver, you'll be able to unscrew the hinges on the top and bottom and adjust them by turning them clockwise or counter-clockwise. After you've repositioned the hinges, shut your window and check for fit. If you're satisfied with the fit of your window, tighten the screws to secure them in the right position.

If you are unable to reposition the hinges, you could need to replace the seal. Over time rubber seals can lose their elasticity and become dry and cause their tightness to decrease. If this happens, it's important to replace the seal as fast as possible to ensure your uPVC windows are watertight and secure from draughts.

UPVC handles can also become loose. This is usually due to screws that have been removed over time, but it could also be due to the mechanism of the handle wears out. Fortunately, it's easy to repair the loose uPVC window handle yourself. You'll first need to close the window and then perform an initial fitting. The joint at the corner of the sash should align with the joint on the casing. If it isn't then you can use a screwdriver or a wrench to loosen the handle and then turn the mechanism back into position.

3. Water Leaks

If you're waking up to wet floors and mouldy walls each time it rains, it's crucial to take action. Leaks of water from windows can cause structural damage to your home and also affect your ability to regulate the temperature of your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

This is an easy fix that can be completed by any DIYer who is competent. Depending on the severity of the problem is, the old caulking might need to be removed. It is crucial to remember that when it is about uPVC window repairs you should not be tempted to 'over-caulk and then make the area harder to clean and can decrease the efficiency of your energy usage.

It is essential to ensure that the drainage holes are clear of debris and that the sill pan is placed properly so that it drains away from the window. In more serious cases, you may need to replace the window.

Mold spots and rotted sills are also signs of water leakage. This fungus thrives in damp conditions and can quickly spread throughout the home.

It is also important to remember that if the leakage originates from the glass of your double glazed windows, it's more likely to be a problem with the glass seal, rather than the frame or sliding. Again this can easily be corrected by an uPVC window specialist who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or loose and open in a breeze It could be the hinges that are at fault. They can be replaced by any competent DIYer and can be completed in a matter of minutes.

Like any mechanical component hinges are prone to wear out over time. Changing a window hinge is essentially a very simple procedure, but it is easier to do with someone else to help you hold the frame up.

It is also important to verify that the uPVC hinges are opening and closed in the correct direction. Check for the arrows on each hinge to determine which way the window should be opened.

The issue could be caused by opening the window repairs improperly or due to a poor installation at the factory. Sending us a photo through our website can often resolve the problem. We are happy to offer suggestions.

It is also essential to lubricate the hinges on a regular basis. This can be accomplished by applying a light engineering oil on the hinges. We recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication can allow the window to operate and close more smoothly. It can also stop corrosion and reduce the risk of sticking. It is recommended to do this at least once a year. WD40 and other solvent-based oils are not recommended because they will damage parts of your uPVC window.

5. Draughts

Draughts can be caused by several different things. The hinges can also become misaligned due to wear, which can cause gaps where the sash meets frame. If they're beyond repair, it could be necessary to have them realigned. The second is the interlock, which is located on the hinge of the window, may also become misaligned, again it is possible to give them a good clean, but in some cases it might be necessary to get them replaced.

The second most frequent cause of draughts is the window seals. These are susceptible to being worn out or damaged over time, and allow air to escape through the gaps. Replacing these with high-quality weatherstripping is a good way to stop draughts. Another alternative is to replace the upvc window with low-emissivity glass. this will help in regulating indoor temperatures and will lessen draughts.

Another method of reducing draughts effectively is by using a Draught-exclusion device. These are typically fabric tubes filled with a filler, which can be put on top of your window sill. They can keep your home warm by blocking out cold air.

With a little maintenance and repairs your windows made of upvc will continue to provide an excellent level of security and insulation for your home. It is crucial to keep in mind that all windows will eventually wear out and it may be more cost-effective to simply replace them instead of fixing them. If you are having issues with your upvc windows, it's recommended to seek help from a professional as soon as you can.